It is important to have your house or permanent structure properly grounded if you have electricity in the building. This can help prevent a fire should lightning strike or some other electrical surge be sent towards the building. Installing a grounding rod properly is very important but also much easier than you might think. There are some regulations in areas on what the requirements are, so be sure to check and see what the rules are in your area. You will also want to ask your utility company to mark where any underground lines are so you avoid hitting them when installing the rod.
The first step is to get the right equipment for the job. You may need a post hole digger, shovel, and post driving tool for this job since the rods are usually eight feet long. They are often copper. When you buy one, make sure it is approved material or it will not properly ground your home. This can lead to a very dangerous situation.
Pick your spot first by making sure you are not in a rocky area. Also, be at least a foot to two feet away from the building to avoid rerouting the surge back into the foundation. Finally, you need to dig on the side of the house with the electrical panel.
Once you have the spot selected, begin digging with the post hole digger. If you do not have one, a shovel will do the job just fine. You do not need to dig a wide hole, just as deep as you can.
When the hole is dug, add water. This is to help soften the ground so it will be easier to push the pole into the ground. Being by pushing it by hand. You may have to move it around in a circle to help get it through the packed dirt. There will be one end that is pointed and that one should go into the ground. At some point, you won't be able to hand push it in and will need to move to the next step with the tools.
Once it is a few feet in the ground, grab the other tools to get it to go the rest of the way. The best is a pile driver. This is designed to fit over the pole and allow you to push it in with less effort by lifting and slamming it back down onto the pole. If you do not have one, you might use a two by four to make the surface easier to hit with a hammer or rubber mallet. Hammer the pole until it is either a couple of inches above or level with the hole.
At this point, you will need to attach the ground wire. Some might want to solder it, but the best option is to have a copper clamp designed for this job. The end of the ground wire should be exposed. Make sure to give it some slack so if the wire is hit or bumped it won't pop loose from the clamp.
Finally, fill in the hole. If the rules require the pole to be completely underground, finish hammering it down and fill it in. In any case, it is best to keep it low enough that a lawn mower blade will not hit is. If you placed it a couple of feet from the building, you might consider burying the wire until it comes up next to the building to protect it from weed eaters and lawn mowers.
The first step is to get the right equipment for the job. You may need a post hole digger, shovel, and post driving tool for this job since the rods are usually eight feet long. They are often copper. When you buy one, make sure it is approved material or it will not properly ground your home. This can lead to a very dangerous situation.
Pick your spot first by making sure you are not in a rocky area. Also, be at least a foot to two feet away from the building to avoid rerouting the surge back into the foundation. Finally, you need to dig on the side of the house with the electrical panel.
Once you have the spot selected, begin digging with the post hole digger. If you do not have one, a shovel will do the job just fine. You do not need to dig a wide hole, just as deep as you can.
When the hole is dug, add water. This is to help soften the ground so it will be easier to push the pole into the ground. Being by pushing it by hand. You may have to move it around in a circle to help get it through the packed dirt. There will be one end that is pointed and that one should go into the ground. At some point, you won't be able to hand push it in and will need to move to the next step with the tools.
Once it is a few feet in the ground, grab the other tools to get it to go the rest of the way. The best is a pile driver. This is designed to fit over the pole and allow you to push it in with less effort by lifting and slamming it back down onto the pole. If you do not have one, you might use a two by four to make the surface easier to hit with a hammer or rubber mallet. Hammer the pole until it is either a couple of inches above or level with the hole.
At this point, you will need to attach the ground wire. Some might want to solder it, but the best option is to have a copper clamp designed for this job. The end of the ground wire should be exposed. Make sure to give it some slack so if the wire is hit or bumped it won't pop loose from the clamp.
Finally, fill in the hole. If the rules require the pole to be completely underground, finish hammering it down and fill it in. In any case, it is best to keep it low enough that a lawn mower blade will not hit is. If you placed it a couple of feet from the building, you might consider burying the wire until it comes up next to the building to protect it from weed eaters and lawn mowers.
About the Author:
Find out how to get a high-quality grounding rod by viewing our web pages today. To access our online catalog of high voltage equipment or to learn more about our certifications, click the links at http://www.rossengineeringcorp.com .
Aucun commentaire:
Enregistrer un commentaire